Refrigerator Repair
Dishwasher Repair
Washer Repair
Dryer Repair
Oven Repair
Stove/Cooktop Repair
Freezer Repair
Appliance Installation
Samsung
Bosch
Thermador
Miele
Sub Zero
Bloomberg
Asko
Haier Appliance Repair Services
Your Local Haier Appliance Repair Company
- Haier HRF15N3AGS refrigerator E1 temperature sensor fault
- Haier washer Err2 door lock failure
- Haier GE-platform dishwasher A20 drain timeout
- Haier HLP21N portable washer pump bearing failure
- Haier wine cooler thermoelectric element fault
- Haier HTW10 top-load washer lid switch failure
- Haier dishwasher A09 water heating fault
- Haier HBF05 chest freezer compressor relay failure
- Haier fridge E0 control board communication error
- Haier dryer moisture sensor bar worn fault
Article Reviewed & Technically Verified by Kevin O., Lead EPA-Certified Technician (15+ Years Experience)
Haier has owned GE Appliances since 2016, so many Haier units sold here share GE platforms, control logic, and parts channels — and Haier is especially strong in the compact and portable appliances common in Brooklyn apartments. Faults surface as coded faults: A-codes on dishwashers, Err-codes on washers, E-codes on refrigerators. Brooklyn Appliance Repair NYC diagnoses them by measuring thermistor resistance and pump/fan current draw rather than swapping parts, and finishes most Haier repairs the same day at (917) 997-5264.
Our Happy Customers
- 15+ Years Experience
- Warranty on Parts & Labour
- 100% client satisfaction
- Skilled Technicians
Our Haier Appliance Repair Services
Haier Fridge Repair
Haier refrigerators — from full French-door models to the compact units common in Brooklyn studios — usually fail at the sealed-system fans or the sensor circuit, not the compressor. A warm fresh-food side with a cold freezer points to a stalled evaporator or condenser fan (grinding, then an E9 overtemperature), while an E1/E2 reading means a thermistor drifting out of spec (~10kΩ at 25°C).
Frost that keeps returning is a defrost fault — we test heater continuity and the defrost thermostat rather than manually defrosting and hoping. On inverter-compressor models we verify the drive board before condemning the compressor itself.
Common issues we fix:
- Fresh-food side warm, freezer still cold
- E1/E2 sensor and E9 overtemperature codes
- Grinding or buzzing from the evaporator fan
- Frost sheet returning after defrost
- Ice maker not filling or overfilling
- Compressor running nonstop
- Door not sealing, condensation at the gasket
- E0 control-board communication faults
Haier Dryer Repair
Many Haier dryers are compact ventless or condenser units built for apartments without a vent run, so drying performance hinges on the condenser coil and moisture-sensor bars rather than an exhaust duct. A greasy film on the sensor bars leaves clothes damp at cycle end without a fault; we clean and re-test the bars before touching the heater.
On vented models we check the heater element and thermal cutoff, and on condenser models we flush the condenser and confirm the condensate pump clears. Most Haier dryer repairs wrap up in one visit.
Common issues we fix:
- No heat or insufficient heat
- Clothes still damp after a full cycle
- Moisture sensor not ending the cycle
- Condenser model not draining condensate
- Drum not turning
- Burning or hot-lint smell
- Squeal or thump from rollers or blower
- Control lockups and error codes
Haier Dishwasher Repair
Haier dishwashers, including the slim 18-inch models that fit tight Brooklyn kitchens, run on the GE service platform and report A-series faults. An A20 drain timeout is usually a jammed pump impeller or a debris-blocked filter, and an A09 means the heating element has gone open-circuit (spec ~20Ω) — both of which we confirm by test rather than guess.
An A10 fill fault points at the inlet valve or low supply pressure, while an F40 flow-meter error is often just a detached impeller magnet. We clear the sump, verify the drain routing, and test each part during every Haier dishwasher repair.
Common issues we fix:
- A20 not draining / standing water
- A10 won't fill or fills slowly
- A09 no heat / poor drying
- Dishes cloudy or still greasy
- F3 thermistor and F40 flow-meter faults
- Spray arms not rotating
- Leaks from door or base
- Stops mid-cycle
Haier Freezer & Wine Cooler Repair
Haier chest and upright freezers that stop holding temperature usually have a failed compressor start relay or overload — on a model like the HBF05 we test the relay and windings before deciding between a relay swap and a sealed-system repair. Constant running with heavy frost points instead to a defrost or door-seal problem.
Haier is also a major maker of thermoelectric wine and beverage coolers, and those fail differently: a warm cabinet with no compressor is typically a dead Peltier element or its cooling fan. We diagnose the thermoelectric module and fan circuit directly on those units.
Common issues we fix:
- Not freezing or weak freezing
- Compressor relay clicking, won't start
- Heavy frost or ice sheets
- Freezer runs constantly
- Wine cooler not cooling (thermoelectric fault)
- Door or lid not sealing
- Water pooling or ice clumping
- Temperature swings and sensor faults
Haier Washer Repair
Haier washers span front-load, top-load, and the portable units (like the HLP21N) that Brooklyn renters use where there's no permanent hookup. An Err2 door-lock fault stalls the cycle before fill, Err3 is a motor-communication break in the board-to-motor harness, and Err4 is an out-of-range temperature sensor — each tested at the connector, not replaced on a hunch.
A washer that won't drain is far more often a lint-packed pump filter or scaled inlet screen than a dead pump. We clear and current-test the drain pump, and on portables we check the quick-connect faucet coupling that tends to clog first.
Common issues we fix:
- Err2 door won't lock / won't start
- Err3 motor communication fault
- Won't drain or won't spin
- Portable unit won't fill (blocked inlet screen)
- Excessive shaking or walking
- Leaking from door or underneath
- Musty odor from trapped residue
- Err4 / E0 sensor and board faults
Haier Cooktop Repair
Haier electric and induction cooktops develop unresponsive touch controls, uneven heating, and element failures; gas models add igniter and burner-valve faults. We isolate the specific component — radiant element, induction coil and cooling fan, or spark module — before recommending a part.
On induction tops we confirm pan detection and internal-fan cooling work correctly, since a cooktop that shuts off under load is usually overheating from a blocked vent rather than a failed coil.
Common issues we fix:
- Burner won't ignite / keeps clicking (gas)
- Induction not detecting cookware
- Uneven or weak heat across zones
- Cooktop shutting off under load
- Touch controls unresponsive
- Cracked glass (assessment and options)
- Element stuck on or not heating
- Error codes and control faults
Haier Stove Repair
Haier ranges tend to fail at the igniter, the bake/broil element, or the temperature sensor rather than the whole control. A gas oven that lights slowly or won't hold heat usually has a weak igniter drawing below spec; an electric range that runs hot or cold points at the RTD sensor.
We test switches, relays, and the control board directly and recalibrate oven temperature after any heating-component swap so the range holds its set point.
Common issues we fix:
- Burners not lighting or heating
- Oven temperature inconsistent
- Weak flame or gas smell (gas models)
- Range won't power on
- Control knobs or touch panel not responding
- Igniter clicking that won't stop
- Sparking or tripping the breaker
- F-series error codes on the display
Haier Oven Repair
Haier ovens that underbake or overbake almost always trace to the RTD temperature sensor or a bake element that's lost continuity. An F3 or F4 code on the GE-shared platform points straight at that sensor circuit — open or shorted — and we measure resistance instead of replacing by elimination.
A door that won't lock for self-clean (F9) is the latch motor or switch, not the board. We inspect the element, sensor, latch, and door seal together and verify temperature accuracy before closing the job.
Common issues we fix:
- Not heating / slow preheat
- Runs too hot or too cold
- F3/F4 temperature-sensor codes
- Broiler not working
- Door won't lock / self-clean stuck (F9)
- Bake element visibly damaged
- Display or keypad failures
- Oven shuts off mid-bake
Common Haier Error Codes
Haier appliances display a specific fault code when a component fails. Reading it before we arrive lets us bring the right part and finish most Haier dishwasher repair jobs in one visit. Have your code ready when you call for the quickest estimate.
Haier dishwasher error codes
| Code | Meaning |
|---|---|
| A09 | Heating element failure — element continuity test required (spec: ~20Ω) |
| A10 | Water fill timeout — check inlet valve solenoid and supply pressure |
| A20 | Drain timeout — inspect pump impeller and drain hose routing |
| F3 | NTC thermistor fault — check resistance at 25°C (spec: ~10kΩ) |
| F40 | Flow meter failure — impeller jammed or magnet detached |
Haier oven and range error codes
| Code | Meaning |
|---|---|
| F2 | Oven overtemperature — runaway temp, check RTD sensor and relay board |
| F3 | Open oven temperature sensor (RTD) circuit |
| F4 | Shorted oven temperature sensor circuit |
| F7 | Stuck keypad button — membrane or control fault |
| F9 | Door lock motor / switch failure — won't cycle for self-clean |
Haier refrigerator error codes
| Code | Meaning |
|---|---|
| E0 | Control board communication fault between display and main board |
| E1 | Refrigerator compartment temperature sensor failure |
| E2 | Freezer compartment temperature sensor failure |
| E3 | Defrost sensor fault — open circuit on defrost thermistor |
| E9 | Refrigerator overtemperature — fan or compressor issue |
The codes above are the ones we see most, but Haier appliances can display many others. Call us with your specific code and we’ll confirm whether a Haier washer repair or the relevant service applies to your situation.
Technician Case Studies — Haier Repairs
Diagnostic & Resolution: Tested condenser fan motor current draw — 0.0A (motor stalled from debris accumulation on blade). Cleaned fan blade and confirmed motor restarts. Fresh food section returned to set temperature within 3 hours; condenser outlet temperature confirmed within operating range.
Diagnostic & Resolution: Removed drain pump access cover — pump filter completely blocked with lint and debris. Cleaned filter, confirmed pump motor draws rated current at 1.2A. Full drainage in under 90 seconds confirmed on three test cycles. No parts replaced.
Diagnostic & Resolution: Confirmed defrost heater continuity — heater intact at 22Ω. Tested defrost thermostat — contacts failed open at room temperature (should be closed below 32°F). Replaced defrost thermostat. Defrost cycle confirmed running on schedule; frost fully resolved within 48 hours.
Diagnostic & Resolution: Inspected drain pump — pump impeller jammed with food debris and a small piece of broken utensil. Cleared blockage, confirmed drain pump motor draws rated current. Drainage confirmed in under 90 seconds on two consecutive test cycles. No parts replaced.
Diagnostic & Resolution: Inspected water inlet valve — valve inlet screen 95% blocked with mineral scale. Cleaned screen and tested fill rate. Also found a small calcium deposit inside the valve body partially obstructing flow. Replaced water inlet valve. Unit confirmed filling to correct level within 2 minutes.
Diagnostic & Resolution: Accessed evaporator compartment behind rear panel — evaporator fan motor bearing worn, causing grinding. Replaced evaporator fan motor. Noise eliminated; airflow restored and fresh food section returned to set temperature within 2 hours of repair.
For professional dryer repair or any Haier appliance service, call Brooklyn Appliance Repair NYC at (917) 997-5264. We offer same-day appointments and perform all repairs at your home.
Frequently Asked Questions — Haier Appliance Repair
What Haier appliances do you repair?
My Haier refrigerator shows E1 — what does that mean?
Is Haier the same as GE Appliances?
What Haier problems do you fix most often?
How much does Haier appliance repair cost?
Appliance Repair
Payment Options
Brands We Deal With
- Admiral
- AEG
- AGA
- Amana
- Ariston
- Asko
- Avantgarde
- Avanti
- Beaumark
- Blomberg
- Blue-Star
- Bosch
- Brada
- Brigade
- Bertazzoni
- Cafe
- Capital
- Cavavin
- Cove
- Dacor
- Danby
- Electrolux
- Fagor
- Fisher and Paykel
- Forno
- Frigidaire
- Fulgor
- Gaggenau
- Garland
- GE
- Haier
- Hisense
- Hotpoint
- Ikea
- Insignia
- Jennair
- Kenmore
- Kitchenaid
- LG
- Liebherr
- Magic Chef
- Marathon
- Maytag
- Miele
- Moffat
- Monogram
- Panasonic
- Samsung
- Smeg
- Sub-Zero
- Sunbeam
- Thermador
- Thor
- Viking
- Whirlpool
- White Westinghouse
- Wolf
