Refrigerator Repair
Dishwasher Repair
Washer Repair
Dryer Repair
Oven Repair
Stove/Cooktop Repair
Freezer Repair
Appliance Installation
Samsung
Bosch
Thermador
Miele
Sub Zero
Bloomberg
Asko
Frigidaire Appliance Repair Services
Your Local Frigidaire Appliance Repair Company
- Frigidaire SY EF condenser fan circuit failure
- Frigidaire Gallery i20 dishwasher drain error
- Frigidaire Affinity E47 communication fault
- Frigidaire E64 dryer heating element failure
- Frigidaire gas range igniter not sparking
- Frigidaire ice maker inlet valve failure
- Frigidaire DF defrost circuit error
- Frigidaire refrigerator door gasket worn
- Frigidaire Gallery SpeedClean burner port clog
- Frigidaire Gallery control board error
Article Reviewed & Technically Verified by Dmitry V., Lead EPA-Certified Technician (15+ Years Experience)
Our Happy Customers
- 15+ Years Experience
- Warranty on Parts & Labour
- 100% client satisfaction
- Skilled Technicians
Our Frigidaire Appliance Repair Services
Frigidaire Fridge Repair
Frigidaire Gallery and Professional French door refrigerators run on an Electrolux platform where a SY EF error (condenser fan fault) is the most common Brooklyn call — the fresh food section warms while the freezer stays cold because heat rejection stops without the fan. We test condenser fan motor current draw (spec: 0.2–0.4A), measure the water inlet valve solenoid resistance (~200Ω at the ice maker coil), and check the PureAir Ultra fan circuit separately since it shares a harness with the evaporator board on FPBM-series models.
Frigidaire FPBM French door, Gallery side-by-side, and FFSS-series models are the most common in Brooklyn. We stock condenser fan motors, inlet valves, and NTC temperature sensors for same-day fridge repair on these units.
Common issues we fix:
- Fridge not cooling
- Cooling unevenly
- Freezer cold but fridge warm
- Water leaking under or inside drawers
- Ice maker not making ice
- Loud humming, clicking or fan noise
- Temperature swings, error codes
Frigidaire Dryer Repair
Frigidaire electric dryers use a Pacemaker resistance heating element that reads 10–12Ω when intact — an open-circuit reading confirms element failure and triggers an E64 heater fault code. Gas models present differently: a burned-out hot surface igniter (normal cold resistance: 80–400Ω) produces the same “drum spins, no heat” symptom as a blown thermal limiter, so we test both before ordering parts. Oxidized moisture sensor bars are the most common cause of clothes coming out damp with no error code on Frigidaire Affinity models.
Frigidaire FFED-series electric and FFTW top-load dryers are the most common models we service. Most dryer repair calls complete in one visit with parts on the truck.
Common issues we fix:
- No heat / weak heat / overheating
- Drum not spinning, squealing, thumping, or scraping
- Dryer shuts off early or won’t start
- Long dry times even on high heat
- Burning smell, tripped breaker, or power issues
- Moisture sensor and control board problems
Frigidaire Dishwasher Repair
Frigidaire Gallery dishwashers use the OrbitClean spray arm — a ball-joint spinner that requires 15–25 PSI to rotate correctly. An i30 error means the base-pan float switch has tripped from a water leak; tracing the actual source (usually the door gasket or the pump-housing O-ring) is essential before clearing the code. An i20 drain error on FGHD-series models typically points to a kinked drain hose or blocked coin trap rather than pump failure — we verify drain flow before recommending pump replacement.
Frigidaire FGHD Gallery and FFCD-series dishwashers with PureSteam are the most common models. We carry drain pumps, door gaskets, and control boards for fast dishwasher repair calls.
Common issues we fix:
- Not draining / standing water / slow drain
- Dishes come out dirty, cloudy, or gritty
- Noisy wash cycle, weak spray, or pump issues
- Door won’t latch, won’t start, or stops mid-cycle
- Leaks from door, bottom, or hose connections
- Heater not working / not drying / error codes
Frigidaire Freezer Repair
Frigidaire upright freezers use a bimetal defrost limit thermostat that opens at 55°F to prevent heater overheating. A DF error code points to a defrost circuit fault — we test the defrost heater resistance (spec: 25–40Ω) and the bimetal thermostat continuity separately, because a faulty thermostat leaves the heater intact while still blocking the defrost cycle. Frost buildup on the side walls rather than the back panel usually indicates the fan is running but door gasket leaks are allowing warm, humid air to enter.
Frigidaire Gallery upright and FFFH-series chest freezer models are the most common in Brooklyn. Most freezer repair calls involve defrost parts or door seal replacements, both stocked on the truck.
Common issues we fix:
- Freezer not freezing or weak freezing
- Heavy frost buildup / iced-over back panel
- Door seal problems causing moisture and ice
- Loud fan noise, buzzing, or clicking
- Temperature swings or random shutoffs
- Control board, sensor, and defrost system failures
Frigidaire Washer Repair
Frigidaire Affinity front-load washers and FFTW top-loaders share Electrolux platform electronics but fail differently. An E47 error indicates a main board-to-UI board communication fault — a bulging capacitor on the main board is the leading cause, not a wiring harness issue. An E21 drain timeout most often traces to the coin trap filter being partially blocked; clearing it restores drain speed without any parts. We test drive motor current draw, drain pump flow rate, and door latch switch continuity before issuing any washer repair estimate.
Frigidaire FFFW and Affinity ATF-series front-loaders are the most common Brooklyn calls. We carry main boards, drain pumps, and door boot seals for same-day repairs.
Common issues we fix:
- Not draining / not spinning / stuck mid-cycle
- Leaks, overfilling, or no water entering
- Loud banging, shaking, or off-balance spins
- Door/lid lock problems and startup failures
- Bad odors, residue buildup, or poor rinsing
- Control board, wiring, and sensor problems
Frigidaire Cooktop Repair
Frigidaire Gallery gas cooktops use a SpeedClean sealed-burner system — carbon deposits inside the burner ports cause weak, uneven flame that is often mistaken for low gas pressure. The center burner runs at up to 18,000 BTU through a dedicated spark igniter module; a cracked igniter tip causes constant clicking even after the burner lights. On Frigidaire electric models, the SpaceWise expandable element switches between 6-inch (1,200W) and 9-inch (2,100W) mode via a separate rotary switch that commonly fails, leaving the outer zone at partial power.
We carry igniter assemblies, burner valve kits, and SpaceWise element switches for Gallery gas and electric cooktop repair calls across Brooklyn.
Common issues we fix:
- Burner won’t ignite / constant clicking / weak flame
- Electric element not heating or overheating
- Uneven heating or temperature instability
- Knobs not responding / stuck switches / sparking issues
- Smell of gas, ignition delays, or safety concerns
- Control and indicator light failures
Frigidaire Stove Repair
Frigidaire Professional and Gallery gas ranges trigger an F10 over-temperature error when the oven RTD sensor drifts above spec — the correct reading is 1,080–1,090Ω at 70°F, and anything above 1,200Ω causes premature shutdowns during preheat. Dual-fuel Frigidaire stoves pair a gas cooktop (spec: 4–7” WC manifold pressure) with an electric oven cavity requiring 240V, meaning the gas and electrical sides require separate diagnostic steps.
Frigidaire FGGF Gallery and FPGH Professional ranges are the most common stove repair calls. We stock oven temperature sensors and igniter assemblies for same-day repairs.
Common issues we fix:
- Burners not working / partial flame / slow ignition
- Temperature control issues and unstable heating
- Knobs, switches, or control panel failures
- Electrical faults, tripping breakers, or loose connections
- Unusual smells, noises, or safety-related concerns
- Error codes and intermittent shutdowns
Frigidaire Oven Repair
Frigidaire Gallery wall ovens use an RTD temperature sensor that reads ~1,080Ω at room temperature — readings above 1,150Ω trigger an F3 error (open sensor), while readings below 1,000Ω trigger F4 (shorted sensor), both causing mid-cycle shutdowns. True Convection models add a third bake element behind the fan; uneven baking with convection engaged means testing that element’s resistance (spec: 20–25Ω) before assuming a control board failure. An F11 stuck-key error clears with a power reset but recurs if the touchpad has carbonized internal contacts that need replacement.
Frigidaire FGEW and Gallery series electric wall ovens are the most common oven repair calls from Brooklyn high-rises. We carry oven temperature sensors and control touchpad assemblies for most Gallery models.
Common issues we fix:
- Oven not heating / not reaching temperature / slow preheat
- Uneven baking, hot spots, or convection problems
- Broiler not working or overheating
- Door not sealing, heat escaping, or broken hinges
- Display, keypad, or control board issues
- Error codes, random shutdowns, or electrical faults
Common Frigidaire Error Codes
Modern Frigidaire appliances display error codes when the self-diagnostic system detects a fault. These codes identify the specific component—control relay, temperature sensor, defrost circuit—without disassembly. Share the code with us when you call and we’ll arrive knowing what to expect.
Frigidaire oven repair error codes
| Code | Meaning |
|---|---|
| F0 | Electronic control board failure |
| F2 | Oven temperature runaway / too high |
| F3 | Open oven temperature sensor (RTD) |
| F4 | Shorted oven temperature sensor (RTD) |
| F10 | Over-temperature runaway — sensor drift or relay fault |
| F11 | Stuck function key on control panel |
Frigidaire fridge repair error codes
| Code | Meaning |
|---|---|
| OP | Door open / door sensor fault |
| SH | Temperature sensor short circuit |
| SY EF | Condenser fan circuit failure |
| DF | Defrost circuit failure |
| 5Y CF | Freezer fan circuit failure |
| HI | Refrigerator temperature too high |
Frigidaire dishwasher repair error codes
| Code | Meaning |
|---|---|
| PF | Power failure detected during cycle |
| HO | Water heating too slow — heater or thermistor fault |
| LO | Rinse aid level critically low |
| i20 | Drain restricted or drain pump blocked |
| i30 | Water detected in base pan (float switch triggered) |
| ER | Control board communication error |
Technician Case Studies — Frigidaire Repairs
Diagnostic & Resolution: Tested condenser fan motor — motor drawing 0.0A (failed open). Without condenser fan, heat rejection stopped and fresh food section warmed. Replaced condenser fan motor (5303918549). Both compartments at set temperature within 4 hours of repair.
Diagnostic & Resolution: Tested water inlet valve solenoid at dispenser circuit — coil resistance open-circuit (0Ω vs. spec ~200Ω). Replaced dual water inlet valve (5303918344). Confirmed full cube production and dispenser flow rate at 7 oz/min per specification.
Diagnostic & Resolution: Inspected main control board — capacitor on communication circuit showed visible bulging. Replaced main control board (137008020). Ran five consecutive cycles with no E47 recurrence; all wash, rinse, and spin programs verified functional.
Diagnostic & Resolution: Measured heater assembly element resistance — read open-circuit (spec ~10Ω). Inspected exhaust duct — 50% restriction from lint at exterior vent. Replaced heater assembly (137292700), cleared duct. Drying time confirmed at 45 minutes for cotton load.
Diagnostic & Resolution: Inspected base tray — water present, float switch triggered. Traced leak to door gasket with hairline crack at lower-left corner. Replaced door gasket (154568601), dried base tray, confirmed float switch spring-return. Ran three cycles with no leak or fault recurrence.
Diagnostic & Resolution: Measured oven temperature sensor at room temp — read 1,190Ω (spec 1,080–1,090Ω). Replaced oven sensor (316490000). Calibrated control, verified oven temperature within ±5°F at 350°F and 450°F using calibrated thermocouple probe.
Frequently Asked Questions — Frigidaire Appliance Repair
What Frigidaire appliances do you repair?
How quickly can you repair my Frigidaire appliance?
Is there a warranty on Frigidaire repairs?
My Frigidaire refrigerator shows SY EF — what does that mean?
My Frigidaire oven shows F10 and shuts off during preheat — why?
Appliance Repair
Payment Options
Brands We Deal With
- Admiral
- AEG
- AGA
- Amana
- Ariston
- Asko
- Avantgarde
- Avanti
- Beaumark
- Blomberg
- Blue-Star
- Bosch
- Brada
- Brigade
- Bertazzoni
- Cafe
- Capital
- Cavavin
- Cove
- Dacor
- Danby
- Electrolux
- Fagor
- Fisher and Paykel
- Forno
- Frigidaire
- Fulgor
- Gaggenau
- Garland
- GE
- Haier
- Hisense
- Hotpoint
- Ikea
- Insignia
- Jennair
- Kenmore
- Kitchenaid
- LG
- Liebherr
- Magic Chef
- Marathon
- Maytag
- Miele
- Moffat
- Monogram
- Panasonic
- Samsung
- Smeg
- Sub-Zero
- Sunbeam
- Thermador
- Thor
- Viking
- Whirlpool
- White Westinghouse
- Wolf
